Bạn đang xem bài viết Zk-Pp2K Pwm Dc 3.3-30V 12V 24V Motor Speed Controller Regulator 8A 150W Adjustable Led Dimmer Pulse Duty Ratio được cập nhật mới nhất trên website Mfua.edu.vn. Hy vọng những thông tin mà chúng tôi đã chia sẻ là hữu ích với bạn. Nếu nội dung hay, ý nghĩa bạn hãy chia sẻ với bạn bè của mình và luôn theo dõi, ủng hộ chúng tôi để cập nhật những thông tin mới nhất.
Practical Scenes: 1. LED brightness adjustment, frequency, duty cycle can be adjusted 2. Motor speed adjustment, frequency and duty cycle can be adjusted 3. Drive the solenoid valve to pull and release, automatic cycle, delay output, cycle number (or infinite loop) can be set. 4. Control equipment to turn on and off, do switch fatigue test, voltage sag and other tests to verify the reliability of customer equipment. 5. Delay start load, delay time can be set, after the delay, it will be turned on or intermittently. Features: 1.1 can directly drive LED, motor, solenoid valve and other loads 1.2 Two modes can be selected: PWM mode – frequency (continuous), duty cycle. Note that the number of pulses cannot be set in this mode, and the pulse is always emitted. PULSE pulse mode – positive pulse width time, negative pulse width time, power-on delay start time, and number of pulses are adjustable. 1.3 With start and stop button, can control the output and stop of the signal 1.4 Wide voltage input 3.3-30V, 5.08mm terminal wiring Specifications: Working voltage: 3.3~30V (note that the positive and negative poles Should not be reversed, otherwise it may burn out) Frequency range: 1Hz~150KHz, the accuracy is about 2%. Motor speed control generally chooses 20KHZ Duty cycle range: 0-100%, 1% stepping Number of pulses: 1-9999, or infinite (display '—-' stands for infinity) Delay output time: 0.000s-9999s, the minimum can be set 1ms Positive and negative pulse width length: 0.000s-9999s, the minimum can be set 1ms Output load capacity: less than 8A (MOS switch tube) Output amplitude: The amplitude is equal to the supply voltage (OUT+ is directly connected to the V+ module) Product size: 79mm*43mm*30mm Product Weight: 42g Packing: Anti-static bag Module description: Button operation instructions: PWM Mode (display has "%" for PWM mode) 1. The factory default mode is PWM mode, FREQ+ and FREQ-key set frequency, DUTY+ and DUTY-button set duty cycle; short press STOP button control signal output or stop, stop output is 0, the screen displays "OUT" mark as There is output, otherwise it stops output; the default factory frequency is 1KHZ and the duty cycle is 50%. 2. If you want to switch to PULSE mode, long press the SET button (more than 6 seconds), do not release, you will see the screen change, "%" disappears, it is PULSE mode. PULSE Mode (No "%" on the right side of the display is PULSE mode) 1. The line above the LCD screen displays the positive pulse width time. The P+ and P- buttons set the parameter. The line below the LCD screen displays the negative pulse width time. The N+ and N- buttons set the parameter. Press the STOP button to control the signal output or stop. When the output is stopped, the output is 0. The screen displays "OUT" for output, otherwise it stops output; the default factory positive pulse width is 0.5 seconds and the negative pulse width is 0.5 seconds. 2. Pulse number and delay time setting – In PULSE mode, press and hold the SET button for 2 seconds and then release, enter the pulse number and delay time setting interface, the screen displays SET, it will be turned off and cleared after entering. ;P+ and P- buttons set the delay time, N+ and N- buttons set the number of pulses, the factory default delay time is 0 seconds, the number of pulses is infinite (display —-); then press SET button 2 In seconds, it will automatically return to the pulse interface, press the STOP button, after the delay setting time, start to issue the set number of pulses. If the number of pulses is sent, it will automatically output 0. If the period is not sent, pressing the STOP button will turn off. The output pulse is turned off and cleared, and the set number of pulses is issued each time it is started. Application Operation Examples: 1. PWM output 20KHZ, 60% duty cycle: Select PWM mode, the frequency is set to 20.00, and the duty ratio is set to 060%. 2. The output is turned on for 0.6 seconds and turned off for 0.2 seconds. Infinite loop: select PULSE mode, the positive pulse width is set to 0.600, the negative pulse width is set to 0.200, the delay time is set to 0.000, and the number of pulses is set to — -. 3. Power on or press the start button, delay 5 seconds, then the output is turned on for 0.6 seconds, off 0.2 seconds, infinite loop: select PULSE mode, positive pulse width is set to 0.600, negative pulse width is set to 0.200, delay The time is set to 5.000 and the number of pulses is set to —-. 4. Power on or press the start button, delay 5 seconds, then output high level 10ms low level 10ms pulse 100: select PULSE mode, positive pulse width is set to 0.010, negative pulse width is set to 0.010, delay The time is set to 5.000 and the number of pulses is set to 0100. 5. Power-on delay for 10 seconds, then permanently output signal: select PULSE mode, the positive pulse width is set to a number greater than 0, the negative pulse width is set to 0, the delay time is set to 10.00 seconds, and the pulse number is infinite. (—-). 6.Other applications can explore or consult customer service All setup parameters are not lost when they are turned off. Note: The high-power PWM driver (PP2 and PP2K type) is a MOS switch type output. When the load is not connected, there is no waveform, and the waveform is only after the load is connected. Package Included: 1 x ZK-PP2K PWM DC 3.3-30V 12V 24V Motor Speed Controller Regulator
Giá sản phẩm trên Tiki đã bao gồm thuế theo luật hiện hành. Bên cạnh đó, tuỳ vào loại sản phẩm, hình thức và địa chỉ giao hàng mà có thể phát sinh thêm chi phí khác như phí vận chuyển, phụ phí hàng cồng kềnh, thuế nhập khẩu (đối với đơn hàng giao từ nước ngoài có giá trị trên 1 triệu đồng)…..
Zhiyu Dc 12V 24V 48V 2 Way Cooling Pwm 4 Wire Fan Temperature Controller With Temperature Speed Display And Alarm Function
Features: 1. DC8-60V operating voltage range (it means that the control panel can work in this voltage range; the controller power supply and fan are together in actual work; it must be powered up in accordance with fan power supply requirements, otherwise it will damage the fan). 2. Dual path independent temperature control; it take turns to display two channels’ temperature (-9.9℃to 70.1℃; error <1℃) and Fan Speed (resolution 10rpm; maximum display 999 x 10rpm; more than the speed displaying 999). 3. The low fan speed and temperature control zone are set by pressing buttons with flexible control and large setting range; program will be saved after the setting. 4. Switch stop-rotating alarm function can be set (external connecting AC buzzer keeps beeping; being shut off by default). Performance parameters: 1. Operating voltage: DC8-60V (must be equal to fan voltage; if you use 12v fan, 24v power supply will make the fan burned) 2. Operating Current: control panel operating current 35mA (l2V) 22mA (24V) 3. Control Ability: not be limited by fan current, but fan connector pins on the board do not exceed 3A current; if using larger current fan, please connect fan power supply cable to the main power supply directly! 4. Control Output Range: 10% —l00%(this is the signal output range; the actual situation depends on fan performance) 5. Temperature Probe Specifications: NTC 10K B =3950 6. Temperature Measurement: -9.9℃ to 99.9 ℃, error <2℃ (1% probe with 70℃) 3℃(>70℃) 7. Temperature Control Zone Range: accelerating speed temperature 5-94℃, full speed temperature 10-99℃ 8. Speed Measurement: 10-9990 rpm, exceeding the speed displaying 999; resolution 10 rpm, display unit *10 rpm (speed measurement is based on common 2-pole signal fan design; most of the fans are 2-pole signal) 9. Stop-rotating Alarm Speed: less than 375rpm 10. Circuit dimensions: 65mm*65mm*15mm, location hole center distance 56mm*56mm, diameter 3.2mm Wiring Connecting instructions: Connect blue screw connector to the main power supply (power supply voltage is equal to using fan voltage within 8-60v range); please do not connect reversely; connect “channel 1” and “channel 2” two 4P socket to the fan and the sequence is power supply negative, positive, speed feedback, and PWM Control (For details, see wire connecting diagram below); connecting “thermal 1” and ”thermal 2” to NTC thermistor (parameter 10K B =3950) uses respectively two-channel fan temperature control measuring temperature; connect “beeping” connector to AC buzzer and when stop-rotating alarm is started, fan stop-rotating buzzer keeps beeping. Wiring Connecting Note: Single fan connector let-through current is 3A; if you need to control the higher current fan, please connect the fan power supply cable directly to the main power supply (controller controlling ability has nothing to do with fan current and please consider the power supply cable’s current let-through ability). Display Description: Control board display value by LED display; 4 indicating LED display on the right of the LED display meanings: line 1_two LEDs respectively stands for channel 1’s temperature and speed (x10rpm) and line 2_two LEDs respectively stands for channel 2’s temperature and speed (x10rpm). Under normal operating conditions, the four digit values will take turns to display; quickly switch digit values manually at any time by pressing the "+" "-" button; after the manual switch, it will stay under this digit value for a long time to return to taking-turns displaying. You can block out the channel 2’s display according to your need. Setting Description: 1. Basic speed settings: basic speed setting for adjusting fan speed before temperature control is started, which is the fan speed when it is lower than the accelerating speed temperature. Setting method: press the "OK" button in any operating state and at the moment, channel 1_two LEDs light up at the same time horizontally with LED display showing current setting value (10-100); set the size by pressing the “+”&“-” button and long-press the button to do continuous modification; press “OK” button after the previous setting; enter into channel 2’s basic speed setting; using the same method to do the setting and after the setting, press “OK” button to save it and exit. 2. Temperature control zone and stop-rotating alarm settings: under normal operating state, long-press “OK” button until the display is L**(**is digit value); release the button; channel 1_two LEDs lighting up at the same time horizontally stands for being in channel 1’s accelerating speed temperature setting status; set the digit value (range 5-94, unit: centigrade) by pressing the “+”&“-”button; after the setting press “OK” button to enter into channel 1 full speed temperature status displaying “H**” ; set the amount by the same way (range 10-99, unit: centigrade); after the setting press “OK” button to enter into channel 1 stop-rotating alarm setting; “+”&“-”button setting; “boF” stands for stopping the channel stop-rotating alarm; “boN” stands for starting the channel stop-rotating alarm; after the setting press “OK” button to enter into channel 2’s digit value setting with the same sequence and setting method as the channel 1 did. After the above setting, press “OK” button to exit and save the parameters. 3. Channel 2 displays blocking setting: in control panel power-off state, keep pressing “OK” button to power up it with LED display showing “2on” (starting channel 2 display) or “2oF” (blocking channel 2 display); release “OK” button; set switch blocking by pressing “+”&“-”button; after the setting, press “OK” button again to exit and enter into the normal operating status. 4. Normal and reverse logic mode switch (newly added): disconnect the fan; under controller not being powered up status, at the same time press (keep pressing) “+”&“-” button to power up the controller; at the moment, controller enters into mode choosing status; release the button; press “+”&“-” button again to switch mode: displaying “F-1” is normal mode and displaying “F-2” is reverse logic mode; after the modification, press “OK” button to exit (automatically being saved when exiting) the setting. Setting Note: 1. at speed and temperature zone setting state, if it stays more than 15 seconds without operation, it will automatically exit without saving any data. 2. when the temperature zone is set, the same channel full speed temperature must be higher than its acceleration speed temperature at least 5 degrees centigrade; when you set a temperature digit value not meeting this conditions, the controller will automatically adjust another temperature digit value to ensure the conditions; this is an automatic one-way adjustment and if you need to adjust back, please manually adjust another temperature digit value. 3. channel 2 blocking display settings only affect working status data display and do not affect control and parameter setting (it can work normally). Package included: 1 x Fan temperature controller 2 x Temperature probe 1 x Diameter 12mm length 10cm buzzer
Giá sản phẩm trên Tiki đã bao gồm thuế theo luật hiện hành. Bên cạnh đó, tuỳ vào loại sản phẩm, hình thức và địa chỉ giao hàng mà có thể phát sinh thêm chi phí khác như phí vận chuyển, phụ phí hàng cồng kềnh, thuế nhập khẩu (đối với đơn hàng giao từ nước ngoài có giá trị trên 1 triệu đồng)…..
Waterproof Dc-Dc Converter Buck 12V/24V To 5V 3A 15W Car Power
Thương hiệu OEM Xuất xứ thương hiệu China Xuất xứ china
– Specification:
– Module Properties: DC step-down module (BUCK) – Dimension:65*60*20mm(L x W x H) – Welding wire way, the wiring instructions : Input: red (+) black (-) Output: yellow (+) black (-)
Package Includes:
1Piece DC/DC Buck Converter
Giá sản phẩm trên Tiki đã bao gồm thuế theo luật hiện hành. Bên cạnh đó, tuỳ vào loại sản phẩm, hình thức và địa chỉ giao hàng mà có thể phát sinh thêm chi phí khác như phí vận chuyển, phụ phí hàng cồng kềnh, thuế nhập khẩu (đối với đơn hàng giao từ nước ngoài có giá trị trên 1 triệu đồng)…..
Voltage Boost Module 8-32V Boost To 9-46V 150W Boost Module Adjustable Mobile Power Supply Led 24V 36V
Type: 150W voltage boost modele (non-isolated boost); Power type: regulated power supply; Dimensions: 60*50*20 (mm); Working temperature: -40~+85 degrees (enhance heat dissipation when the ambient temperature is too high); Input voltage: 8-32V; Output voltage: 9-46V continuously adjustable (only boost, output voltage must be higher than the input voltage); Output power: natural heat dissipation 90W, enhanced heat dissipation 150W; Output current: 8A MAX More than 4A, please strengthen the heat dissipation (related to the input and output voltage difference, the larger the differential pressure, the smaller the output current).
Product List: Voltage Boost Module 1pcs
Note 1: Due to manual measurement, there will be a deviation of 1-3cm. The data is for reference only, please refer to the actual product; Note 2: The color may differ slightly from the picture, due to different resolution on different computer monitors.
Giá sản phẩm trên Tiki đã bao gồm thuế theo luật hiện hành. Bên cạnh đó, tuỳ vào loại sản phẩm, hình thức và địa chỉ giao hàng mà có thể phát sinh thêm chi phí khác như phí vận chuyển, phụ phí hàng cồng kềnh, thuế nhập khẩu (đối với đơn hàng giao từ nước ngoài có giá trị trên 1 triệu đồng)…..
Cập nhật thông tin chi tiết về Zk-Pp2K Pwm Dc 3.3-30V 12V 24V Motor Speed Controller Regulator 8A 150W Adjustable Led Dimmer Pulse Duty Ratio trên website Mfua.edu.vn. Hy vọng nội dung bài viết sẽ đáp ứng được nhu cầu của bạn, chúng tôi sẽ thường xuyên cập nhật mới nội dung để bạn nhận được thông tin nhanh chóng và chính xác nhất. Chúc bạn một ngày tốt lành!